IIS30", 36" and 48" Custom Hood InsertZVC3OLSSZVC36LSSZVC48LSS49-80415 I12-06 JRMonogram°
Installation PreparationTOOLS AND MATERIALS REQUIRED(NOT SUPPLIED)Aluminizedduct tapeSiliconePencil and tape measure S _Safety glasses"_ _ _;:_ _
Installation PreparationPARTS PROVIDEDLocate the parts packed with the hood.CHECK INSTALLATION HARDWARECount screws/components. Screwsshown actual siz
Wall Installation PreparationDUCTWORK, WIRING LOCATIONSDetermine the exact location of the insertsleeve. Mark the exact centerline location.The ceilin
Island Installation PreparationCONSTRUCT CEILING SUPPORT (for Island Installation)Plan the Location of the Hood and DuctworkThe ceiling structure must
InstallationPreparationREMOTE MOUNTING OF THE CONTROL(WIRED}-- ILWARNING: Disconnectelectricalpower from unit before beginning remote controlinstallat
InstallationPreparationREMOTE MOUNTING OF THE CONTROL(WIRED) {CONT.)COUNTERTOPWALL MOUNTControl• , _"-"r"--..Connecto r4-wire cordi-._&
Installation Instructions[STEP I] INSTALL HOOD LINER1. Frame the cutout opening to fit the linenNOTE: The opening support must be 3/4" thickwood
Installation Instructions[STEP 2] CONNECT ELECTRICALVerifg that power is turned off at the source.WARNING: ,fhouse wiring is not2-wirewith a ground wi
Installation InstructionsISTEP 31 INSTALL INSERT SLEEVE1. Tuck the house wiring out of the wag.2, Install the insert sleeve into the cutout opening of
Installation Instructions[STEP 4] INSTALL DAMPER PLATE1. Pick up damper plate assemblg and rotate so that °vent side is up and bracket is located on l
Installation InstructionsBEFOREYOU BEGINRead these instructions completelg andcarefullg.• IMPORTANT- Save these instructions for localinspector's
Installation InstructionsISTEPslINSTALL BLOWER MOTORiioooooii1. Pick up blower motor and rotate so tabs alignwith damper plate bracket.2. Insert blowe
Installation InstructionsISTEP7] INSTALLFILTERS1.Remove protective film from the filters.Clip2. Tip the filter into the back tab slots and lift up.Whi
Notes22
Printed in ItalgNote: While performing installations described in this book,safety glasses or goggles should be worn.For Monogram ® local service in y
Installation InstructionsAVERTISSEMENT:AFIN DEREDUIRELERISQUED'INCENDIE,DECHOCSELECTRIQUESOU DE BLESSURESCORPORELLES,VEUILLEZVOUSCONFORMERAU×RECO
Design InformationCONTENTSDesign InformationProduct Clearances ...4Product Dime
Design InformationPRODUCT DIMENSIONSZVC30 Dimensions and Specifications (in inches)Outside Dimensions27-1/2_The custom canopg must be sized to fit the
Design InformationPRODUCT DIMENSIONSZVC36 Dimensions and Specifications (in inches)Outside Dimensions27-1/2"The custom canopg must be sized to fi
Design InformationPRODUCT DIMENSIONSZVC48Dimensions and Specifications (in inches)Outside DimensionsI" 39-1/2"© © ©The custom canopy must be
Advance PlanningADVANCE PLANNINGDuctwork Planning• This hood is equipped for 8" round ductwork.• Determine the exact locution of the vent hood,•
Advance PlanningDUCT FITTINGSUse this chart to computemaximum permissible lengths forduct runs to outdoors.NOTE: Do not exceed maximumpermissible equi
Kommentare zu diesen Handbüchern